Latest threads in Ford Mustang Forumshow only best voted threads

Subject Author Posted Replies
 
Odd gas prices (no rhyme, no reason?) Toronto
So, oil shoots to $69 barrel, prices of gas hit $1.27/L. Then, oil falls to $57 barrel, prices of gas drop to $0.83/L. So far, so good. That was over a few months.. Recently, the price (with oil going...
4
4
 
Where the blazes is Clifford
I can't find clifford performance's web site. I need info on how to modify a mustang inline 6.
10
10
 
Autopower roll bar install question
Hi Folks, I bought an autopower 4 point street roll bar to install in my '66 coupe. I tried a google search to see pictures on how to cut the interior rear quarter panels to fit but can't find...
 
WANTED: 1987 Mustang GT 5.0 w/T-Tops
Looking for a 1987 Mustang GT 5.0 w/T-Tops Need one that is Medium Red w/Dark Grey GT Skirts and Premium GT Rims for that year. Should be 5-speed with Grey or black interior Car should be low miles as...
8
8
 
motor switch
i have a 96 stang with a 3.8 and i know that that was the year for the 4.6 not the 5.0 and im wondering what problems am i going to run into with that switch since everyone says the k member is...
1
1
 
Cost to change spark plugs in a 2001 GT
I don't know if anyone recalls this, but I complained about an intermittent throttle/timing issue a few months back. Last week, the "intermittent" problem became "all the damn time." I'd start her up,...
6
6
 
Concensus on the 4.6 engine
I am looking at the 2006 Mustang GT convertible. This is something that I plan on using only on weekends and for fun - something that I want to keep and hand down to my son 20 years from now. How is...
16
16
 
97 Headlights
Got new ultra clear headlights for my son's 97 V6--what we didn't get was instructions/directions on how to change them out. I've seen instructions someplace on the web but can't seem to find them...
2
2
 
86 2.3 mustang camshaft alignment problem.
The timing belt broke on my son's 86 2.3 Mustang. The timing pointer that you align the timing mark on the camshaft sprocket with is missing. Is there any other thing that I can use to align the mark...
1
1
 
What's my compression ratio? (head swap question)
I have 62cc heads currently and my CR is 9.62:1. If I switch to 64cc heads what would my CR be then? 58cc? What's the math?
3
3
 
Dodge admits fault with Charger
Note the suggestions by enthusiasts which they FINALLY listened to, assuming this car (the Challenger) comes out in late 2007.
1
1
 
PROTOTYPE 1967 PONTIAC 400 HEADS-CAST#061-EBAY-ONE CENT !
one-year only "spherized wedge" cast iron Pontiac D-port heads, casting #061 will fit 350-389-400-421-428-455 Pontiac engines low mileage untouched castings- never had a valve job or cut yet- no...
 
Help My thrust bearing failed why??
This is a small block Ford. I'm running a AOD-E tranny. The engine is about 4 months old. Could there be a issue with the tranny? The tranny wasn't changed but the engine was completey new. The...
4
4
 
Hybrids to take it on the chin
They have, and there has been much public discussion about it, since they hit the market. EPA Fuel Economy Ratings Have Shortfalls Of Up To 50 Percent Window Stickers Vastly Overstate MPG, Consumer...
6
6
 
Nightline does piece on the resurgence of muscle cars
Challenger, Mustang and maybe a Camaro. Aimed (said Nightline) at 60 year old baby boomers? I doubt they'll be confined to that demographic. But, they did point out one thing; There would be nothing...
12
12