Questions regarding 4WD not engaging on a 1991 Chevy K1500 Pickup

Hi everyone,

My 4WD stopped engaging on my 1991 Chevy K1500 Pickup. I noticed the

4WD light was not coming on and I ran the truck up on the bottom of a steep bank to check if it was not in 4WD or if it was just the 4WD indicator light. Only the rear wheels were spinning and it definitely was not in four wheel drive.

I had just used the 4WD a few days ago when I ran the front of the truck up on ramps so that I could spray some rust inhibitor and undercoating on it. The wax based rust inhibitor and waxed based black undercoating were made by

formatting link
and are approved by GM and Chrysler. The rust inhibitor is a "cavity wax" that is sprayed inside of doors and body panels but you can also spray it underneath the vehicle if you want. It's supposed to be safe for electrical connections but I guess I could have sprayed some on a connector and caused a problem. I'm sure I did not get any of the actual black undercoating on any electrical connectors, but perhaps I got some of the cavity wax on the connectors. I had also blew everything off underneath with some compressed air, but I did not notice any connectors near the air nozzle. I'm not sure if something happened or if it is just coincidence. I also greased the fitting on the front drive shaft, but I don't see how that would cause a problem like this.

After I backed the truck down off the ramps I parked it I left it in

4WD (I forgot I even had it in 4WD). Today I took the truck for a short trip to the park and when I got there, I noticed that the selector lever was in 4WD but the truck did not feel like it was in 4WD on my trip. When leaving the park, I move the selector to 2WD and drove for a while and then moved it to 4WD so see if it would engage and it would not go into 4WD. Neither the 2WD or the 4WD light show up on the selector console on the floor.

The GM factory manual said to check the A/C-HTR fuse. I checked the A/ C-HTR fuse and it was fine. However, I had a 25 amp fuse labeled 4WD and when I checked it, it was blown. I had a 15 amp fuse in a drawer and I put that in just to see if it would get things working. However, that fuse was blown almost immediately.

I was going to get some 25 amp fuses from NAPA tomorrow and see if those fuses would work, but I suspect that those fuses will blow as well.

The manual says if it's not the fuse then it's the "transfer case switch" or the transfer case linkage is disconnected or not adjusted properly. The manual also says it could be a faulty transfer case or front differential, but I'm guessing it's probably the switch, provided the proper 25 amp fuse keeps blowing tomorrow.

How many switches are on the transfer case ? The manual says it's on the left upper side of the transfer case. I think the 4WD indicator light switch is a completely separate switch from the switch that actually engages the 4WD. Can I check the switch with an Ohms meter to verify if it is faulty or not ?

The transfer case housing is aluminum so I hope it's not a nightmare getting the old switch out without stripping threads. The switch that I saw looks very hard to get to.

If it's not the switch or a mechanical problem with the transfer case or front differential, what else could it be ?

My only guess would be wiring or a rusted or faulty connection. I seriously doubt it's a mechanical problem with the transfer case or front differential, I've changed all the fluids at recommended intervals, and have never had any noise or shifting problems with the drive-train. There is about 100,000 miles on the truck now.

I would appreciate any feedback, advise, or similar experiences anyone could relate.

Thanks John

Reply to
John2005
Loading thread data ...

Sounds like the actuator on the front axle has failed. Not uncommon. Or it could be the switch. Easy way to test is to replace the fuse, then disconnect the front axle actuator. Connect up a tester to the terminals and see if you get 12 volts when you hit the switch. If you do the circuit and switch is OK and the actuator is bad. If not it could be the switch or the relay.

Reply to
Steve W.

Thanks Steve W.

John

Reply to
John2005

Hi Steve,

One of my new 25 amp 4WD fuses blue immediately when I tried it.

I pulled the connector off the front axle actuator, installed a new fuse, and with the key on and the selector in 4WD, I am getting 12 volts on my multimeter at the front axle actuator feed connector, so the front axle actuator is getting voltage. I guess this means the switches on the transfer case and the wiring up to the front axle is in all likelihood OK, since I am getting 12 volts at the actuator ? If the selector is in 2WD, my multimeter said it was getting .02 volts, I guess some bleeds through anyway or it's just the meter.

I was going to pull the front axle actuator out, plug it in and hit the key to see if it will move just be be sure, my guess is that it will just blow a fuse which would indicate that it's bad. The fuse did not blow with the actuator Un-plugged and the key on while I was testing for voltage.

There appear to be two switches on the axle housing. One which according to a parts picture I have is the front axle actuator, it is mounted horizontally on the front axle and it has a black connector. The other switch or sensor is above the front axle actuator and looks smaller. The second smaller switch has a white connector and is more out of sight and on top of the axle housing whereas the axle actuator seems easy to get to. What does the second switch or sensor do ?

Both connectors are mounted to a thin piece of stamped steel that is screwed to a small platform on the passengers side aluminum axle tube with a single screw . Will the black connector for the axle actuator slide off of this steel mount ? It looks very rusted and would not seem to come off when I pulled on it unless there is a trick ?

When I take the old axle actuator out, it appears the wire will twist around and around unless I can get the connector off the mount. That wont matter if the part is bad, which my gut tells me it is, but I still have to get the thing off in order to replace it. I don't want to break the steel clip or a plastic connector and I'm not crazy about spraying it with a rust buster since it's an electrical connection.

Any other feedback would be appreciated.

Thanks John

Reply to
John2005

I was able to wiggle the actuator connector off the stamped metal support, it looked worse (more rusted and stuck) than it really was. I took the 4WD actuator out, connected it back up, installed a new fuse, hit the key, selected 4WD and the actuator did not move. It also blew the fuse once again.

I picked up a new 4WD actuator from NAPA-Balkamp for $62.00 which beats dealer list of around $212.00.

I'm going to install it next time I get a little time and the weather is decent. If it does not work I will check back but I suspect it will work.

Thanks again, John

Reply to
John2005

I installed the new actuator and the 4WD is working again :-)

The 4WD light is now on, and of course I tested the truck on a hill to actually makes sure the 4WD is working. However, the light to indicate

2WD is not working. I suspect that it must be a burned out bulb since the 4WD light is working. The light may have been burned out for a long time since I never pay it much attention. I may replace it when I get time.

As long as the truck goes down the road in 2WD and I have 4WD when I need it, I'm in good shape.

Perhaps I did not really have 4WD when I went up the ramps, or perhaps the 4WD actuator just had one more push left in it. I"m just glad I found this & got it taken care of before I really needed the 4WD this winter.

Thanks again for your feedback Steve. John

Reply to
John2005

My 95 Silverado is doing the same thing...Is my truck different than his 91 ??? Or would the advice remain the same ????

Reply to
benick

Reply to
connorkuester55

Reply to
connorkuester55

I have a 1989 Chevy 2500 that won't go n 4wheel drive transfer case is working n actuator working but still not working if anyone could tell me what could be the problem let me know

Reply to
jlecates8

The front drive shaft will turn when put in 4wheel drive but I'm not getting any type of traction to the front tires

Reply to
chevymarcus2018

MotorsForum website is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.