Latest threads in General Ford Forumshow only best voted threads

Subject Author Posted Replies
 
Fusion AWD 2008 LH stabilizer link replacement
LH Rear Stabilizer bar clunking. Looks like the piece of the link connecting to the bar is missing half its little rubber boot so I suppose water got in there and now its loose and clunking. Can this...
 
88 escort headlights only work when the high beam lever is pulled back,
I have replaced both the headlight switch and the dimmer switch and the switch connector, auto parts store sold me a relay but cant find where it is
 
need help on 2002 ford escort zx2 with 2.0 doc
I am in need of help. My husband ran my car very hot. It blew my Thermosta t housing into two pieces. N broke my timing belt. I had to tear my motor down n replace all my gaskets thermostat housing n...
1
1
 
faulty belt determination and replacement?
I have an '03 Taurus wagon 3.0 OHV the is squeaking a lot from the passenger side. I believe it is one of the belts, but how do I go about determining which one it is? Once determined, how do I...
4
4
 
delayed illumination of light
2012 ford mustang. i do not drive this car daily. one tire has a very slow leak, need to air it up about every month or two so i forget about it. i start the car and drive away, but the low tire...
1
1
 
1999 Mercury Sable problems
Hello! I'm trying to help out a friend with a problem she's having with he r Sable. This started two or three weeks ago. After driving for 15-25 blocks the ca r will start to act as tho it running out...
1
1
 
MIL light on, two new codes on my 2000 Sable Vulcan OHV
Well, less than 6 weeks after my ordeal with the defective pcb valve, the engine light came on yet again today. Upon scanning, I am finding codes PO135 and PO155. I haven't yet done a data record...
17
17
 
cheapest scanner that shows live data?
Looking for recommendations for a cheap OBD scanner that not only shows codes, but live data including fuel trims. Graphing is not necessary. Thank you.
7
7
 
ford explorer ignition replacement
How much should I have to pay for ignition replacement in a 1999 ford explorer?
 
two 3.0 OHV based cars, one with rough idle
I've been having a time with my 2001 Sable. I recently changed out the plugs/ wires as the car has 125K miles and the plugs hadn't been changed. The car at idle seems kind of rough and I thought the...
6
6
 
busted wiring harness replacing cam synch on my 03 Taurus, how to remedy?
I replaced my cam synch today on my Taurus 03 Vulcan ohv. However, in the process while trying to reach the cam, there was that darn wiring harness as seen here: I accidentally broke this so that a...
1
1
 
burning oil smell in vents
2001 mercury sable - for years now, there is a burning oil smell coming through the vents when turning on the vent trying to get outside air. I have looked for the leak and on hot surfaces and for...
1
1
 
spark plugs, fuel trims
All of the spark plugs and new wires arrived and I changed the three front plugs/ wires yesterday. Not sure whether or not the originals had ever been changed. I have some questions for the group: 1)...
19
19
 
1990 e 350 ignition key hard to turn
The ignition key feels like it is gummed up and is very hard to turn. R&R or replace?
2
2
 
intake manifold plenum gasket replaced; pcv valve replaced--- still problems
I think I may need some more help. To catch you up, the vacuum leak was coming from the pcv valve boot on the side against the manifold. It made the appearance that smoke was coming from the plenum...
19
19