Dodge Trucks Forum

  1. Home
  2. Dodge Trucks Forum
4831 Threads Posts
to

OT: Frontload washers

My GE toploader sometimes walks around a little bit, then I have to shove it back into the corner. Frontloading models...
17 comments posted 18yrs
posted by flyingterrapin
17 comments posted 18yrs posted by flyingterrapin

junp a battery + to -

I have a 1999 dodge Durango and my daughters friend jumped batteries and the put the cable on the wrong pole + to - and...
4 comments posted 18yrs
posted by detap
4 comments posted 18yrs posted by detap

08 Dodge 1500 prices

Dealer here has an 08, 1500, short bed, V6, six speed truck for $13,999. Trying to figure out if that's a good deal or...
10 comments posted 18yrs
posted by nospamsal1
10 comments posted 18yrs posted by nospamsal1

My last Dodge/Chrysler Purchase

http://www.daimlerchryslervehicleproblems.com/ Mike
22 comments posted 18yrs
posted by nospam
22 comments posted 18yrs posted by nospam

2000 Ram Van Blower Motor Location?

Got a 2000 dodge ram van 1500. Where the heck is the blower motor and the resistor? Thought it would be underneath the i...
2 comments posted 18yrs
posted by mattwmc2001
2 comments posted 18yrs posted by mattwmc2001

OT: Log homes

My parents are wanting to build themselves a log home and have asked me to see what I could find out with regards to ma...
54 comments posted 18yrs
posted by cooltoys
54 comments posted 18yrs posted by cooltoys

They Found Denny

Denny was found after gorging himself on WC. News story at 10p. http://cellar.org/iotd.php?threadid=9188 Bob
4 comments posted 18yrs
posted by ram1220
4 comments posted 18yrs posted by ram1220

preventive maint. on Dodge with diesel

Hey Group I have wanted a Dodge with a diesel engine for a long time and finally bought one. It is 96 model 2500 with 1...
4 comments posted 18yrs
posted by bridgescharles
4 comments posted 18yrs posted by bridgescharles

OT Jeep project is finished!!!

Finally done. Man I hate following into a project, spend more time undoing other folks alleged good work. Denny we were...
65 comments posted 18yrs
posted by Roy
65 comments posted 18yrs posted by Roy

head gasket not flat question

I am replacing my head gaskets for my new aluminum cyl head instal using felpro 1044 (0.51 which it calls for) I have b...
2 comments posted 18yrs
posted by oopsIfartedted
2 comments posted 18yrs posted by oopsIfartedted

Selling Dodge pick-up

I'm considering selling my Dodge p/u. Is this the correct group or is there another?
18 comments posted 18yrs
posted by kc5koh
18 comments posted 18yrs posted by kc5koh

OT Poll!!!! Who wins???

Super Tuesday who wins?? Dem and Repub. Pick a winner in each. After the super bowl I'm not picking anything for a bit....
98 comments posted 18yrs
posted by Roy
98 comments posted 18yrs posted by Roy

Creaking noise, 2001 Dakota

I've posted about this before; I had the dealer do the tsb that resets the steering wheel, but the sound is still there...
9 comments posted 18yrs
posted by NOnewsgroupsSPAM
9 comments posted 18yrs posted by NOnewsgroupsSPAM

Dodge Sprinter question

What, if any is the standard for replacement of brake rotors? Is it typical to replace them whenever pads are replaced,...
0 comments posted 18yrs
posted by rbm
0 comments posted 18yrs posted by rbm