Cherokee Winches

Dec 25, 2004 7 Replies

I'm picking up a Warn 8000 or 9000lb winch used from a friend for CHEEAAP today. I know it works because it was on my old truck which I sold to him.



I'd like to mount it via a front reciever for now, as I like the idea of being able to remove the winch when I am not wheeling. I live in an urban area and I'm concerned the winch will be stolen.



Is this the way to go?

formatting link
What type of receiver do I need to get?



Thanks,



Carl


Carl

I use a Draw Tite front receiver on my 97 GC and it works very well. It is a bolt on installation in place of the front skid plate, includes two tow eyes and does not interfere with the existing tow hooks. It required no cutting of the bumper fascia to install and decreased the approach angle just a bit. I think they also make a unit for the Cherokee,.

On my 88 Cherokee I fabricated a front receiver that mounted to the factory tow hook mounts. I'm a mechanical engineer and was able to design and then weld it up. If you go the "build" route be warned that

8 or 9000# requires a good bit of steel to handle that load. Your idea to buy rather than build is the way to go.

Howard

Thanks Howard. Where did you get the draw tite receiver from? Is it better to weld or bolt on? How much did it cost? Will I rip the reciever off?

Thanks,

Carl

Are these two parts what I need? Will I have any problems with the hitch ripping from my frame? Can I bolt it on and then weld it as well?

formatting link
formatting link
Thanks again,

Carl

Carl I f I remember correctly Jeep does not allow any welding of the frame because the heat may affect the strength of the steel. Both my GC and the Cherokee were bolt on. Just remember to use the included hardware and check them for tightness. Draw Tite seems to be available just about everywhere. I happened to live about 5 miles from one of their warehouses so my auto parts store could get one the same day with no shipping charges. I tend to try and buy local just in case and to keep them in buisness. Of course it depends where you are located. Regards

Howard

added next, boil an additional 11 minutes. Put the live babies into the boiling water and cover. Boil till meat comes off easily with a fork.

Oven-Baked Baby-Back Ribs

Beef ribs or pork ribs can be used in this recipe, and that is exactly what your dinner guests will assume! An excellent way to expose the uninitiated to this highly misunderstood yet succulent source of protein.

2 human baby rib racks 3 cups barbecue sauce or honey glaze (see index) Salt black pepper white pepper paprika

Remove the silverskin by loosening from the edges, then stripping off. Season generously, rubbing the mixture into the baby?s flesh. Place 1 quart water in a baking pan, the meat on a wire rack. Bake uncovered in 250° oven for 1½ hours. When browned, remove and glaze, return to oven and bake 20 minutes more to form a glaze. Cut ribs into individual pieces and serve with extra sauce.

Fresh Sausage

If it becomes necessary to hide the fact that you are eating human babies, this is the perfect solution. But if you are still paranoid, you can substitute pork butt.

5 lb. lean chuck roast 3 lb. prime baby butt 2 tablespoons each: salt black, white and cayenne peppers celery salt garlic powder parsley flakes brown sugar 1 teaspoon sage 2 onions 6 cloves garlic bunch green onions, chopped

Cut the children?s butts and the beef roast into pieces that will fit in the grinder. Run the meat through using a 3/16 grinding plate. Add garlic, onions and seasoning then mix well. Add just enough water for a smooth consistency, then mix again. Form the sausage mixture into patties or stuff into natural casings.

Stillborn Stew

By definition, this meat cannot be had altogether fresh, but have the lifeless unfortunate available immediately after delivery, or use high quality beef or pork roas

Howard -

This is the winch I have:

formatting link
Mine is the older style which has the controller plug in on the front of the selonoid pack.

formatting link
That mounting plate doesn't look like it will accomodate my winch. I didn't see any on the Warn site that will accomodate it either. I suppose I could mount it with the mounts down, and just bolt the fairlead to the two holes in the plate. but I think the winch might be too deep. I could also mount it upright with the plate between the fairlead and the winch, but I'm concerned about only having two bolts hold the winch down.

Ideas? Is the 8274 a decent winch?

Thanks,

Carl

formatting link

Join the Discussion

Have something to add? Share your thoughts — no account required.

Didn't find your answer?

Ask the community — no account required