Lexus GS300 owner's manual: Electrical components

ELECTRICAL COMPONENTS

294

ELECTRICAL COMPONENTS

295

ELECTRICAL COMPONENTS

CHECKING BATTERY CONDITION

Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas.

• Do not cause a spark by contacting the battery terminals with tools.
• Do not smoke or light a match near the battery. The electrolyte contains poisonous and corrosive sulfuric acid.
• Avoid contact with eyes, skin or clothes.
• Never inhale or swallow electrolyte.
• Wear protective safety glasses when working near the battery.
• Keep children away from the battery.

EMERGENCY MEASURES

• If electrolyte gets in your eyes, flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the medical office.
• If electrolyte gets on your skin, thoroughly wash the contacted area. If you feel a pain or burn, get medical attention immediately.
• If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediately take off the exposed clothing and follow the procedure above, if necessary.
• If you accidentally swallow electrolyte, drink a large quantity of water or milk. Follow with milk of magnesia, beaten raw egg or vegetable oil. Then go immediately for emergency help.
• Warning: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

296

ELECTRICAL COMPONENTS

Checking battery exterior

1 Terminals 2 Hold-down clamp

Check the battery for corroded or loose connections, cracks, or loose hold–down clamps.

1. If the battery is corroded, wash it off with a solution of warm water and baking soda. Coat the terminals with grease to prevent further corrosion.
2. If the connections are loose, tighten the clamp bolts – but do not overtighten.
3. Tighten the hold–down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

NOTICE

• Make sure the engine and all accessories are turned off before performing maintenance.
• When checking the battery, remove the ground cable first and reinstall it last.
• Be careful not to cause a short circuit with tools.
• Take care no solution gets into the battery when washing it.

297

ELECTRICAL COMPONENTS

Checking battery condition Checking by indicator

Check the battery condition by the indicator color. 1 BLUE – Good condition. 2 WHITE – Charging necessary. Have the battery checked by your Lexus dealer. 3 RED – Have the battery checked by your Lexus dealer.

NOTICE Do not refill the battery with water.

BATTERY RECHARGING PRECAUTIONS

During recharging, the battery is producing hydrogen gas. Therefore, before recharging:

1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
2. Make sure the power switch on the recharger is off when connecting the charger cables to the battery and when disconnecting them.

CAUTION

• Always charge the battery in an unconfined area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.
• Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may explode causing personal injuries.

NOTICE Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

298

ELECTRICAL COMPONENTS

CHECKING AND REPLACING THE BLADE TYPE FUSES

►Driver’s side kick panel

►Passenger’s side kick panel

►Engine compartment 1 Spare fuses 2 Pull-out tool

►Engine compartment

1. Turn the ignition switch off and open the fuse box lid. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse.

299

ELECTRICAL COMPONENTS

2. Make sure the inoperative component is turned off. Pull the suspected fuse straight out with the pull-out tool and check it. If it has blown, push a new fuse into the clips.

►Good ►Blown

a. Look carefully at the fuse. If the thin wire is broken, the fuse has blown. If you are not sure or if it is too dark to see, try replacing the suspected fuse with one of the same value that you know is good.

b. Install only a fuse with the amperage rating designated on the fuse box lid.

If you do not have a spare fuse, in an emergency you can pull out the "CIG", "RAD NO.1" or "OBD" fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same.

If you cannot use one of the same amperage, use one lower than, but as close as possible to, the amperage. If the amperage is lower than that specified, the fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clips.

300

ELECTRICAL COMPONENTS

It is a good idea to purchase a set of spare fuses and keep them in your vehicle for emergencies.

If the new fuse immediately blows out, there is a problem with the electrical system. Have your Lexus dealer correct it as soon as possible.

CAUTION Never use a fuse with a higher amperage rating, or any other object, in place of a fuse. This may cause extensive damage and possibly a fire.

CHECKING THE CARTRIDGE TYPE FUSES

▶Engine compartment

301

ELECTRICAL COMPONENTS

►Good ►Blown

If the headlights or other electrical components do not work and the blade type fuses are O.K., check the cartridge type fuses. If any of the cartridge type fuses are blown, they must be replaced.

If there is an overload in the circuits from the battery, the fuses are designed to blow before the entire wiring harness is damaged.

NOTICE Before replacing the fuses, have the cause of electrical overload determined and repaired by your Lexus dealer.

CAUTION Always use a genuine Lexus fuse or equivalent for replacement. Never install an ordinary wire – even for a temporary fix. This may cause extensive damage and possibly a fire.

302

ELECTRICAL COMPONENTS

ADDING WASHER FLUID

If the washer tank becomes nearly empty, add washer fluid.

You may use plain water as washer fluid. However, in cold areas where temperatures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Lexus dealer and most auto parts stores. Follow the manufacturer's directions for how much to mix with water.

NOTICE Do not use engine antifreeze or any other substitute because it may damage your vehicle's paint.

CHECKING THE HEADLIGHT AIM

► 1 Beam angle gauge (vertical movement for low beam) 2 Beam angle gauge (horizontal movement for low beam) 3 Beam angle gauge (vertical movement for high beam) 4 Beam angle gauge (horizontal movement for high beam)

Before checking the headlight aim:

1. Be sure that the body around the headlight is not deformed.
2. Park the vehicle on a level spot.
3. The driver gets into the driver's seat and puts the vehicle in a state readying for a driving (with a full tank).
4. Bounce the vehicle several times.

303

ELECTRICAL COMPONENTS

Adjusting the headlight aiming (low beam)

▶ 1 Adjusting bolt A 2 Adjusting bolt B

▶ 1 Bubble 2 Acceptable range

Vertical movement gauge: The bubble of the gauge should not deviate from the center of the gauge by more than 2 marks to either side of the gauge.

If the bubble is out of the acceptable range of the beam angle gauge, adjust it using bolt A and B.

304

ELECTRICAL COMPONENTS

1. Turn the bolt A in either direction using a Phillips-head screwdriver. At this time, keep the turning direction and number of turns in mind.

2. Turn the bolt B the same number of turns and in the same direction as step 1 using a Phillips-head screwdriver.

305

ELECTRICAL COMPONENTS

► 1 Mark 2 Acceptable range

Horizontal movement gauge: The mark should not deviate by more than one mark to either side of the gauge.

It the edge of the lens is out of the acceptable range of the beam angle gauge, adjust it using bolt B.

If the error is over the value specified above, take the vehicle to your Lexus dealer to adjust the headlight aim.

After adjusting the headlight in the vertical direction, check that the light has been shifted from the adjusted position in the horizontal direction.

Adjusting the headlight aiming (high beam)

► 1 Adjusting bolt A 2 Adjusting bolt B

306

ELECTRICAL COMPONENTS

1 Bubble 2 Acceptable range

Vertical movement gauge: The bubble of the gauge should not deviate from the center of the gauge by more than 2 marks to either side of the gauge.

If the bubble is out of the acceptable range of the beam angle gauge, adjust it using bolt A.

Turn the bolt A in either direction using a Phillips-head screwdriver.

307

ELECTRICAL COMPONENTS

1 Red line 2 Acceptable range

Horizontal movement gauge: The red line should not deviate by more than 2 blue lines to either side of the gauge. If the red line is out of the acceptable range of the beam angle gauge, adjust it using bolt B.

Turn the bolt B in either direction using a Phillips-head screwdriver. If the error is over the value specified above, take the vehicle to your Lexus dealer to adjust the headlight aim.

308

ELECTRICAL COMPONENTS

REPLACING LIGHT BULBS

The illustrations on the following pages show the locations of light bulbs. If it is necessary to replace a bulb, take your vehicle to your Lexus dealer as soon as possible. Use bulbs with the bulb numbers and wattage ratings given in the table.

CAUTION

• To prevent burning yourself, do not replace the light bulbs while they are hot.
• Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

Vehicles with discharge headlights:

• Do not touch the high voltage socket when the headlights turn on. 20000 V is momentarily generated and may cause severe injury by electric shock.
• Do not disassemble, repair or take apart the headlight bulbs, connector, power supply circuits and rotated components. Or you may be injured by electric shock. Call your dealer when the headlights fail to work or have to be replaced or disposed of.

NOTICE

Only use a bulb of the listed type.

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the fogging is caused by the temperature difference between the outside and inside of the lens, just like the windshield fogged up in the rain. However, if there is a large drop of water on the inside of the lens, or if there is water pooled inside the light, contact your Lexus dealer.

309

ELECTRICAL COMPONENTS

LIGHT LOCATION

\begin{tabular}{|l|l|l|l|} \hline Light Bulbs & Bulb No. & W & Type \ \hline [1] Headlight (Low beam) & & & \ \quad Discharge bulb & D2R & 35 & B \ \quad Halogen bulb & HB4 & 51 & C \ [2] Front turn signal light & — & 21 & D \ [3] Headlight (High beam) & HB3 & 60 & A \ [4] Parking light & — & 5 & D \ [5] Fog light & HB4 & 51 & C \ [6] Front side marker light & 194 & 3.8 & D \ \hline \end{tabular}

\begin{tabular}{|l|l|l|l|} \hline Light Bulbs & Bulb No. & W & Type \ \hline [1] Trunk light & 194 & 3.8 & D \ [2] High mounted stoplight & — & 5 & D \ [3] Tail/stop light & — & 5/21 & D \ [4] Tail light & — & 5/21 & D \ [5] Rear turn signal light & — & 21 & D \ [6] Back-up light & 921 & 16 & D \ [7] Tail/stop light & — & 5/21 & D \ [8] License plate light & — & 5 & D \ \hline \end{tabular}

ELECTRICAL COMPONENTS

A: HB3 halogen bulbs
B: D2R discharge bulbs
C: HB4 halogen bulbs
D: Wedge base bulbs
E: Double end bulbs
F: Single end bulbs

311

312

SECTION 6 – 5

SERVICE PROCEDURES AND SPECIFICATIONS

Body

• Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........ 314
• Protecting your vehicle from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........ 315
• Washing and waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........

BODY

SPECIFICATIONS

– DIMENSIONS AND WEIGHT

*Unladen vehicle

– FUEL TANK

| Capacity | 75 L (19.8 gal., 16.5 Imp.gal.) |

314

PROTECTING YOUR VEHICLE FROM CORROSION

Proper care of your Lexus can help ensure long-term corrosion prevention.

The most common causes of corrosion to your vehicle are:

• The accumulation of road salt, dirt and moisture in hard-to-reach areas under the vehicle.
• Chipping of paint or undercoating caused by minor accidents or by stones and gravel.

The following conditions will cause or accelerate corrosion of your vehicle, so it is important to keep your vehicle, particularly the underside, as clean as possible and to repair any damage to paint or protective coatings as soon as possible.

• The presence of road salt or dust control chemicals, salt in the air near the sea coast, industrial air pollution.
• High humidity, especially at temperatures just above freezing point.
• Certain parts of your vehicle are wet or damp for an extended period of time, even though other parts of the vehicle are dry.
• Components of the vehicle which do not dry quickly due to lack of proper ventilation are exposed to high ambient temperature.

BODY

To help prevent corrosion on your Lexus, follow these guidelines:

Keep your vehicle clean by regular washing. In addition, observe the following points.

• If you drive on salted roads in the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize corrosion.
• High pressure water or steam is effective for cleaning the vehicle's underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing them. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.
• Wash the underside of the vehicle thoroughly when winter is over.

See "Washing and waxing" on page 316 for more tips.

Check the condition of your vehicle's paint and trim. If you find any chips or scratches in the paint, touch them up immediately to prevent corrosion from starting. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

315

BODY

Check the interior of your vehicle. Water and dirt can accumulate under the floor mats and could cause corrosion. Occasionally check under the mats to make sure the area is dry. Be particularly careful when transporting chemicals, cleansers, fertilizers, salt, etc. These should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area.

Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly ventilated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp and it will cause corrosion. Even if your garage is heated, a wet vehicle can corrode if the ventilation is poor.

WASHING AND WAXING

Washing your Lexus

Keep your vehicle clean by regular washing.

The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as possible.

• When driving in a coastal area
• When driving on a road sprinkled with antifreeze
• When having coal tar, tree sap, bird droppings and carcass of an insect
• When driving in the areas where there is a lot of smoke, soot, dust, iron dust and chemical substances
• When the vehicle becomes remarkably dirty with dust and mud

Hand-washing your Lexus

Work in the shade and wait until the vehicle body is not hot to the touch.

1. Rinse off loose dirt with a hose. Remove any mud or road salt from the underside of the vehicle or in the wheel wells.
2. Wash with a mild car-wash soap, mixed according to the manufacturer's instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard – let the soap and water remove the dirt.

316

BODY

Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic substance splashes an ornament, be sure to wash it off with water and check if the ornament is damaged.

CAUTION Do not attach the heavily damaged plastic wheel ornament. It may fly off the wheel and cause accidents while the vehicle is moving.

Aluminum wheels: Use only a mild soap or neutral detergent. Urethane bumpers and side moldings: Wash carefully. Do not scrub with abrasive cleaners. The bumper and side molding faces are soft. Road tar: Remove with turpentine or cleaners that are marked safe for painted surfaces.

NOTICE Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may be toxic or cause damage.

3. Rinse thoroughly – dried soap can cause streaking. In hot weather you may need to rinse each section right after you wash it.
4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard – you might scratch the paint.

Automatic car wash Your vehicle may be washed in an automatic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you whether the process is safe for the paint on your vehicle.

Waxing your Lexus Polishing and waxing is recommended to maintain the original beauty of your Lexus' finish. Apply wax once a month or if the vehicle surface does not repel water well.

1. Always wash and dry the vehicle surface before you begin waxing, even if you are using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become extremely weathered, use a car-cleaning polish, followed by a separate wax. Carefully follow the manufacturer's instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint.
3. Wax the vehicle again when water does not bead but remains on the surface in large patches.

317

BODY

CLEANING THE INTERIOR

CAUTION

• Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from activating correctly, resulting in serious injury.
• Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or under the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Leather Interior

The selected leather is used in your Lexus. Due to characteristics of leather products, some parts of leather may be rough, uneven or scratched originally.

To keep good appearance, we recommend you to clean it periodically twice a year.

Remove dirt on the leather in the following ways:

1. Wipe it off lightly using a soft cloth (e.g. gauze) dampened with 5% solution of neutral detergent for wool.
2. Wring water from a clean cloth and thoroughly wipe off all traces of detergent with it.
3. Wipe off the surface of the leather with a dry soft cloth. Allow the leather to dry in a ventilated shaded area. Excess of wet may cause the hardening or shrinking of the leather.

NOTICE

• Dirt or sand adhered to the leather may damage the treated surface and cause it to wear earlier. Remove dirt or sand using a vacuum cleaner.
• If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.
• Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for cleaning the leather as these could cause discoloring.
• Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.
• Mildew may develop on soiled leather upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.
• Long exposure to direct sunlight may cause the leather surface to harden and shrink. Keep your vehicle in a shaded area, especially in the summer.
• The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.

318

BODY

• Improper cleaning of the leather upholstery could result in discoloration or staining.

Synthetic Leather Areas (Dash and sun visors)

The synthetic leather areas may be easily cleaned with a mild soap or detergent and water.

First vacuum over the upholstery to remove loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the synthetic leather. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt does not come off, repeat the procedure. Commercial foaming-type cleaners are also available which work well. Follow the manufacturer's instructions.

NOTICE Do not use solvent, thinner, gasoline or window cleaner on the interior.

Carpets, Windows and Seat Belts

Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to produce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water – the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely.

The seat belts may be cleaned with mild soap and water or with lukewarm water.

Use a cloth or sponge. As you are cleaning, check the belts for excessive wear, fraying or cuts.

NOTICE

• Use a good foam-type shampoo to clean the carpets.
• Do not use dye or bleach on the belts – it may weaken them.
• Do not use the belts until they become dry.
• The windows may be cleaned with any household window cleaner.
• When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires.

319

BODY

Air Conditioning Control Panel, Car Audio, Instrument Panel, Console Panel, and Switches

Use a soft damp cloth for cleaning.

Soak a clean soft cloth in water or lukewarm water then lightly wipe off any dirt.

NOTICE

• Do not use organic substances (solvents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discoloring, staining or peeling of the surface.
• If you use cleaners or polishing agents, make sure their ingredients do not include the substances mentioned above.
• If you use a liquid car freshener, do not spill the liquid onto the vehicle's interior surfaces. It may contain the ingredients mentioned above. Immediately clean any spill using the method mentioned above.

If you have any questions about the cleaning of your Lexus, your local Lexus dealer will be pleased to answer them.

320

SECTION 7

REPORTING SAFETY DEFECTS FOR U.S. OWNERS

Reporting safety defects for U.S. owners

• Reporting safety defects for U.S. owners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........ 322

321

REPORTING SAFETY DEFECTS FOR U.S. OWNERS

REPORTING SAFETY DEFECTS FOR U.S. OWNERS

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-25-LEXUS).

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.

To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

322

WE REALLY CARE ABOUT YOU - PLEASE BUCKLE UP

Lexus has made a special effort to encourage use of seat belts.

Lexus belts are:

• Comfortable
• Easy to use
• Convenient

We encourage you to use your belts every time you drive.

2003 GS430/300 from May '03 Prod. (OM30601U)

GS4/300 (U)

GAS STATION INFORMATION

• Fuel selection: Select premium unleaded gasoline with an Octane Rating of 91 (Research Octane Number 96) or higher for optimum engine performance. However, if such premium type cannot be obtained, you may temporarily use unleaded gasoline with an Octane Rating as low as 87 (Research Octane Number 91).

• Fuel tank capacity: 75 L (19.8 gal., 16.5 Imp.gal.)

• Engine oil: “Toyota Genuine Motor Oil” or equivalent

  Oil grade: API grade SL “Energy-Conserving” or ILSAC multigrade engine oil.

  Recommend oil viscosity – SAE 5W–30 if normal temperatures are below 38°C (100°F)

  Oil capacity: L (qt., Imp.qt.) | Drain and refill | GS430 | GS300 | | --- | --- | --- | | with filter | 5.2 (5.5, 4.6) | 5.4 (5.7, 4.8) | | without filter | 4.9 (5.2, 4.3) | 5.1 (5.4, 4.5) |

  See page 260 for detailed information.

• Engine coolant: Capacity: GS430: 9.0 L (9.5 qt., 7.9 Imp.qt.) GS300: 7.7 L (8.1 qt., 6.8 Imp.qt.)

  Coolant type – "Toyota Genuine Long Life Coolant" or equivalent

  With ethylene–glycol type coolant for a proper corrosion protection of aluminum components

For checking the engine coolant, see page 264.

Do not use alcohol type antifreeze or plain water alone.

• Automatic transmission: Fluid type – “Toyota Genuine ATF Type T–IV”

  See page 270 or 274 for detailed information.

• Tire information: See page 282 through 289 for detailed information.

• Tire pressure: Tire size: GS430 – 225/55R16 94V or 235/45ZR17 GS300 – P215/60R16 94V or 225/55R16 94V

  Tire pressure: cold tires kPa (kgf/cm² or bar, psi)

For sustained high speeds above 160 km/h (100 mph), in countries where such speeds are permitted by law, add the tire pressure given below to the front tires and rear tires, but never exceed the maximum cold tire pressure molded on the tire sidewall.

You should know as much about the quality and importance of proper maintenance of your new vehicle as the people who built it.

The Lexus authorized Repair Manual tells you how to maintain your vehicle and enables you to correctly perform your own maintenance.

The best way to keep your new vehicle in top running order is to maintain it properly from the moment you drive it off the showroom floor.

The Lexus authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.

cm–1

Maintenance procedures for the engine, chassis, body, electrical system, and more, are clearly explained and illustrated.

Periodic maintenance and tune-up

Periodic maintenance and tune-up helps to prevent small problems from growing into larger ones later on. The repair manual outlines exactly what maintenance is required and clearly explains how to do the work yourself step-by-step.

Areas covered include such things as spark plug replacement, valve clearance adjustment and engine oil and filter replacement.

Where to obtain the Repair Manual

The repair manual for GS430, GS300, written in English, may be purchased as applicable from any Lexus dealer. Pub. Name: 2003 GS430, GS300 Repair Manual Pub. No.: Vol.1 974U1 Vol.2 974U2

cm-2