Land Rover 4WD vehicles

painting mi landy, advise sought.

just prepping the tub for its annual makeover due to the capping having lost part of its galvenising ill have to paint...

6 comments posted 22yrs

posted by death

6 comments posted 22yrs posted by death

S3 SWB rear springs query

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello there Spent a few (!) hours last weekend replacing the rear springs...

5 comments posted 22yrs

posted by g1bwt

5 comments posted 22yrs posted by g1bwt

range rover dead...

hello, Would the ignition module from a 3.9 fit on the distributor of a 1990 3.5. I think the spark is weak, and have ch...

5 comments posted 22yrs

posted by bern

5 comments posted 22yrs posted by bern

a few bits fs.

Out of a 1989 land rover 90. Set of seats. Grey in colour with checked pattern. Drivers,passengers and one for the midd...

0 comments posted 22yrs

posted by hectichouse2005

0 comments posted 22yrs posted by hectichouse2005

Valve adjustment 300Tdi

Hi just a couple of brief questions. When adjusting or checking the clearances of the valves on a Discovery 300 Tdi, sh...

7 comments posted 22yrs

posted by mark

7 comments posted 22yrs posted by mark

For Sale - Series 11, SWB 3/4 Ragtop

1966 Series 11 for sale, 3/4 Ragtop, Complete stripdown and ground up restoration. All major work done to chassis and b...

6 comments posted 22yrs

posted by igundwane

6 comments posted 22yrs posted by igundwane

Cold Start Light not working

Hi Guys further to my previous post (thanks to Simon and David for advice). The reason I haven't seen the cold start li...

5 comments posted 22yrs

posted by j.l.troyano

5 comments posted 22yrs posted by j.l.troyano

Defender Tomb Raider Information etc

Can anyone point me to sources of further information and discussion highlighting the Tomb Raider Defender special edit...

1 comments posted 22yrs

posted by usenet

1 comments posted 22yrs posted by usenet

Disco gearbox counterweight??

Landrover Folks No response to my previous post which perhaps contained too much background info. - I have now reduced...

0 comments posted 22yrs

posted by invalid

0 comments posted 22yrs posted by invalid

Welding with Disco

Hi all, I bought a mig welder and have been practising for a couple of weeks now and I reckon I am ready to tackle the...

7 comments posted 22yrs

posted by andrew.hart.i hate spam

7 comments posted 22yrs posted by andrew.hart.i hate spam

Who wanted 2.6 Exhaust manifold?

Someone on this NG emailed me a while back about an exhaust manifold and/or exhaust system for a SIII 2.6. I was planni...

1 comments posted 22yrs

posted by nospam.alex

1 comments posted 22yrs posted by nospam.alex

Towing with Freelander 2.0 diesel

Hi there I am just about to purchase a Freelander 2.0 diesel primarily as a run about but with the occasional use as a...

1 comments posted 22yrs

posted by jim_nicholson99

1 comments posted 22yrs posted by jim_nicholson99

Chipping a Freelander 2.0 diesel

Hi there I am looking to purchase a 1998 Freelander 2.0 diesel which has done 67,00 miles. My initial reaction on the t...

1 comments posted 22yrs

posted by jim_nicholson99

1 comments posted 22yrs posted by jim_nicholson99

Disco overdrive?

Hi guys. Reading another post (Thread: Another series query...) brings to mind something I've been thinking about for a...

5 comments posted 22yrs

posted by news

5 comments posted 22yrs posted by news

S3 Starting Help please.

Hi all I have recently bought an 1983 Series 3 with 2.25 diesel engine to tow/launch a boat with. Bit of a stupid quest...

2 comments posted 22yrs

posted by j.l.troyano

2 comments posted 22yrs posted by j.l.troyano